FREE PRACTICE / DRAW AND VERIFY

Five free 2D CAD practice exercises, with measurements.

Learning CAD gets easier when you actually draw something and check whether the numbers match. These five practice drawings progress from a simple measured rectangle to basic floor-plan and site geometry. They're software-agnostic: you can use any 2D drafting program, including CADstart's browser demo. Try each exercise before opening its answer check.

By Jesse Velazquez · CAD designer with 20+ years of hands-on experience

Choose your first drawing

New to CAD? Start with the mounting panel, then work through the other drawings. Review coordinates and snaps if you need a refresher.

Open the free CAD demo

Practice in your browser. Read about the full course if you want more information first.

Before you draw: units, accuracy, and your own answer key

An X,Y coordinate describes a position, not a width and height: X is horizontal and Y is vertical. For example, opposite corners at (10,10) and (40,30) make a rectangle 30 units wide and 20 units high. Subtract the starting coordinate from the ending coordinate to check each dimension.

Work in a single unit system for each drawing. Enter the coordinates and sizes instead of placing objects by eye. Use a line, rectangle, circle, polyline, offset, trim, layers, and dimensions as needed. If a command is unavailable in your current program, draw the same measured geometry another way.

Start with separate OUTLINE, DIMENSIONS, and CENTERLINES layers when practical. Snaps such as endpoint, midpoint, and center help keep geometry connected. You do not need a printer, a paid software license, or any existing CAD file to attempt these exercises.

Begin each challenge on a clear area of the workspace, save your work if your software allows it, then check the listed dimensions. The coordinates are practice inputs, not real manufactured, architectural, or surveyed designs.

  • Exercises 1–3 use abstract drawing units; millimeters work well if your software asks for units.
  • Exercise 4 uses inches for a full-size architectural drafting exercise.
  • Exercise 5 uses feet on a fictional parcel and is not a survey or buildable-lot determination.
  • Use the hidden answer checks as a way to verify your geometry—not as a substitute for drawing it.
  1. Choose the exercise's stated units and put the main geometry on OUTLINE.
  2. Draw the shapes using the listed coordinates, lengths and radii.
  3. Dimension the stated critical widths, heights and center spacing.
  4. Open the exercise's answer check and compare measured results.
  5. Correct any missing endpoint connection or unit mistake before proceeding.

Exercise 1: a rectangular mounting panel with four holes

Skills: rectangles, circles, coordinates, center snaps, and horizontal/vertical dimensions. Work in millimeters or dimensionless practice units. All coordinates are absolute X,Y values. This drawing is a learning exercise, not a cut-ready part.

  1. Draw a rectangle from (10,10) to (130,90).
  2. Place a circle of radius 6 at each center: (25,25), (115,25), (25,75), and (115,75).
  3. Put overall width and height dimensions outside the panel.
  4. Dimension the horizontal spacing between left and right circle centers and the vertical spacing between rows.
  5. Check that all four circles are the same size and that neither their centers nor their outlines fall outside the rectangle.
  6. Optional: copy the first circle to the other three measured positions rather than redrawing it by eye.
Check your drawing against the answer

The panel measures 120 wide × 80 high. Horizontal hole-center spacing is 90; vertical row spacing is 50. Each hole diameter is 12. Every hole center sits 15 from the nearest horizontal and vertical panel edge. If your annotations show a different number, check the coordinate inputs and dimension snaps.

Exercise 2: centered concentric circles

Skills: circle center/radius entry, center snaps, centerlines, and diameters. This checks whether you can make two circles share exactly one center rather than only appearing centered at a particular zoom.

  1. Draw a reference rectangle from (20,20) to (180,120).
  2. Find its center with midpoint snaps or calculate the mid-X and mid-Y coordinates.
  3. Draw a circle of radius 20 at the rectangle center.
  4. Draw a second circle of radius 35 using that same center point.
  5. Add horizontal and vertical centerlines through both circles on a CENTERLINES layer.
  6. Dimension both circles by diameter and verify the outer circle fits entirely within the rectangle.
Check your drawing against the answer

The rectangle measures 160 × 100 with center (100,70). The inner diameter is 40 and outer diameter is 70. The outer circle has 15 clearance to the top and bottom edges and 45 clearance to the left and right edges. Both circle-center markers must coincide.

Exercise 3: stepped profile using a connected polyline

Skills: connected segments, corners, precision editing, and checking closed geometry. Imagine a simple flat outline—not a 3D extrusion or a fabrication drawing.

  1. Start a polyline at (10,10).
  2. Continue through (150,10), (150,40), (110,40), (110,85), and (10,85).
  3. Close the polyline back to (10,10), without leaving a tiny final gap.
  4. Dimension the total width, total height, bottom-step height, and right-step width.
  5. Check the corners at high zoom using endpoint snaps and confirm the outline is closed.
  6. If your program can calculate a closed profile's area or perimeter, compare those results to the answer check.
Check your drawing against the answer

Overall width is 140 and height is 75. The lower step is 30 high and the right-hand extension is 40 wide. The outline contains six straight edges, area 8,700 square units and perimeter 430 units. An open or doubled-up segment may cause different results.

Exercise 4: a basic measured room outline

Skills: changing units, wall thickness with Offset, dimensioning, and translating drafting numbers into a readable floor-plan sketch. Use inches for this exercise; it is not a building-code-compliant plan.

  1. Set drawing units to inches and draw an outer rectangle from (0,0) to (144,120).
  2. Create a second inner rectangle by offsetting each outer wall inward by 6 inches. Your inner corners should be at (6,6) and (138,114).
  3. Put the walls on a WALLS layer; put dimensions on DIMENSIONS.
  4. Dimension the outer width and height in inches, then calculate each in feet.
  5. Dimension the clear interior width and height between the inner wall lines.
  6. Optional drafting practice: mark a 36-inch-wide hypothetical doorway opening along the bottom wall, but do not assume this sketch is ready for construction.
Check your drawing against the answer

The overall outline is 144 × 120 inches (12 × 10 feet). Six-inch offsets create clear inner dimensions of 132 × 108 inches (11 × 9 feet). The clear rectangular floor area is 99 square feet. A correct inward offset reduces each overall dimension by 12 inches, not by 6.

Exercise 5: a fictional site with setback guides

Skills: 2D civil drafting fundamentals, closed outlines, setback offsets and measured location of a building footprint. Use feet. Real property boundaries, easements, utilities, zoning setbacks, drainage, and construction approvals must come from verified documents and qualified review; this is a fictional geometry exercise only.

  1. Draw a hypothetical parcel rectangle from (0,0) to (100,80) on a PROPERTY layer and label it PRACTICE — NOT A SURVEY.
  2. Create guide lines 10 feet inward from all four sides. Put these hypothetical setback guides on a separate SETBACKS layer.
  3. Draw a fictional building-footprint rectangle from (25,20) to (55,60).
  4. Dimension the parcel width/height, setback distance, and building-footprint width/height.
  5. Check that the footprint stays within the interior guide rectangle and note its closest distances to those guides.
  6. Add a north arrow labeled ASSUMED NORTH and a legend distinguishing property, setback guides, and footprint.
Check your drawing against the answer

The fictional parcel is 100 × 80 feet. Uniform 10-foot guides enclose an 80 × 60 foot rectangle (4,800 square feet before any real-world constraints). The building footprint measures 30 × 40 feet. It sits 15 feet right of the left setback guide, 35 feet left of the right guide, and 10 feet inside both the lower and upper guides. Nothing in this exercise establishes that an actual site could be built on.

How to tell whether your drawing is genuinely accurate

A shape can look correct while its endpoints are a fraction apart or its dimensions reference the wrong object. Review each drawing as though someone else must use it. Zoom into corners, check circle centers, confirm line closure, and verify that the dimensions reflect geometry rather than manually typed labels.

If you get stuck, go back to your last correct coordinate instead of deleting everything. Learning to diagnose one misplaced endpoint is a transferable CAD skill. Repeat a challenge without the steps once you have passed it.

  • Check exact width, height, radius or diameter, and center-to-center distances.
  • Keep dimensions separate from outlines so annotations do not crowd the geometry.
  • Use actual endpoint/midpoint/center snaps instead of visual guesses.
  • Distinguish drafting practice from real engineering, surveying, or permit drawings.
  1. Repeat Exercise 1 with its coordinates shifted 200 units right, preserving relative spacing.
  2. Repeat Exercise 3 from memory using only the six corner coordinates.
  3. Choose one exercise and annotate it cleanly enough that another beginner can read its dimensions.
  4. Save a before-and-after copy where your CAD software allows saving.
  5. Try CADstart's free browser demo if you'd like to practice the same concepts in a guided 2D workspace.
READY TO DRAW?

Put these fundamentals into practice.

Start with the free CADstart demo and decide whether the guided 2D course is for you.

See CADstart & the free demo →